|
|
Post by popeye on Jun 13, 2008 22:11:08 GMT -5
what no invite  |
|
|
|
Post by Rock Dawg on Jun 15, 2008 12:06:40 GMT -5
What is this for? Hmmm..  |
|
|
|
Post by Rock Dawg on Jun 15, 2008 12:10:28 GMT -5
|
|
|
|
Post by Rock Dawg on Jun 15, 2008 12:13:09 GMT -5
|
|
|
|
Post by Rock Dawg on Jun 15, 2008 12:15:29 GMT -5
I was in such a hurry to get it painted before dark, I remember to clean the slags off of the flat plates. That will have to wait until we get back.
|
|
|
|
Post by Rock Dawg on Jun 15, 2008 12:17:53 GMT -5
lets see... What else.. oh YA! I got the video camara mounted.    I would see if it shakes by doing a test drive before we leave. ;D It is nice because it has a quick disconnect to remove it so we can video the other rigs easly. |
|
|
|
Post by The Black Jeep on Jun 15, 2008 12:58:42 GMT -5
I like It  |
|
|
|
Post by Rock Dawg on Jun 15, 2008 23:48:02 GMT -5
I did a couple test videos today. I added some fur to the mic so it will not pick up the wind as bad. I secured the video camara but it still shakes. Byas tires... I think the shake is in the jeep, not the video cam.
Got the rear winch wiring finished with the fuse in the power line by the battery so I will not have any issues with it.
Drilled a couple holes in the roll cage base plates but they come out 1/2 on a brace so I can not bolt them down the way I wanted to.
Wanted to get the tires changed and jeep put in trailer today but never got around to it. I ended up building a garden box and addind some super grow dirt instead.
|
|
|
|
Post by mudslinger97117 on Jun 16, 2008 0:06:42 GMT -5
Looking good Rusty.. What about the trailer? Are you a go then?
|
|
|
|
Post by boggerboy on Jun 16, 2008 9:59:38 GMT -5
Nice lookin really good rusty im diggin the cam |
|
|
|
Post by Rock Dawg on Jun 16, 2008 10:40:06 GMT -5
Looking good Rusty.. What about the trailer? Are you a go then? Yes I checked out the bearings and replaced the tires. I have to get the replacement pieces for the top, change the tires and load them. |
|
|
|
Post by ReBeL on Jun 16, 2008 14:03:55 GMT -5
looks great rusty great job |
|
|
|
Post by Rock Dawg on Jun 16, 2008 15:23:48 GMT -5
Finally, I got spare axle shafts today. They are 27 splined so I home they work. I could have the 30 spline chrome molly axles also. The only way to tell is to take them out. Either way. I have the outer one. It is the same on both sides.
|
|
|
|
Post by WILLYNILLY on Jun 17, 2008 21:42:58 GMT -5
cool!! let us know how the winch works on the suckin the axle down! Im jealous been wanting to do that for a long time!
|
|
|
|
Post by Rock Dawg on Jun 19, 2008 10:07:05 GMT -5
cool!! let us know how the winch works on the suckin the axle down! Im jealous been wanting to do that for a long time! The rear winch is pretty cool. It has a pre set 6" adjustment on it. I just have to "tap" the button on the remote and the winch will either suck down 6" or relase 6". Of course if I hold the button it will work like a normal winch, but the tap feature is great for what i am using it for. I have it set for 5" of slack, so when I tap the "A" button, it takes up the slack and pulls the suspention down just 1". This way I can have a slight load on it and it will not release the suspention when going down hills, and with a tap of the "B" button, I have 5" of slack, two tapes 11", if needed.  |
|
