|
Post by Buzzer on Sept 27, 2006 20:19:08 GMT -5
1. clutch kit 2. flywheel 3. rear oil seal/front tranny seal 4. trans jack 5. flywheel line up tool
ok now what am i missing? lol the list just keeps going and going....
|
|
|
Post by vegaguy76 on Sept 27, 2006 21:42:41 GMT -5
1. clutch kit 2. flywheel 3. rear oil seal/front tranny seal 4. trans jack 5. flywheel line up tool ok now what am i missing? lol the list just keeps going and going.... I may have the clutch alignment tool. I've got a few hanging next to the toolbox with "ford" cast into them. I'll bring them along as well. Charlie
|
|
|
Post by yamxer438 on Sept 28, 2006 4:28:22 GMT -5
if its gonna be nothin but a wheeler i'd bob the bed just for better clearance
|
|
|
Post by Buzzer on Sept 28, 2006 14:53:56 GMT -5
love the gloss orange on flat black...
|
|
|
Post by Buzzer on Oct 1, 2006 21:59:29 GMT -5
|
|
|
Post by MudHog on Oct 7, 2006 15:21:53 GMT -5
lookin more and more like a trail rig every time i see it!!! cant wait to see how it does out on the trails
|
|
|
Post by Buzzer on Oct 9, 2006 17:23:11 GMT -5
got the rear diff... clean'ed and fluid changed(royal purple) and someone mentioned putting some flames on the front, think they turnned out ok-as i have never done them before...
|
|
|
Post by Jonny tsunami on Oct 9, 2006 19:49:47 GMT -5
OK, easy, easy, set the Orange spray paint down it will be alright and carefully back away before someone gets hurt. Just kidding I like the Orange looks good.
|
|
|
Post by Buzzer on Oct 9, 2006 20:10:55 GMT -5
OK, easy, easy, set the Orange spray paint down it will be alright and carefully back away before someone gets hurt. Just kidding I like the Orange looks good. lmao!!!! don't worry only have 1/2 can left... for the other side.....just need to do the inside the bed and nerf bar/roll bar black primer....
|
|
RangerWheelin
lil wheeler
To many projects and not enough time
Posts: 24
|
Post by RangerWheelin on Oct 9, 2006 21:57:13 GMT -5
Looking good, Not so sure about that orange though lol.
did you figure out how to get that dash panel to work?
|
|
|
Post by Buzzer on Oct 10, 2006 8:06:25 GMT -5
yeah i moded it a bit ... not the best - but it works.....
|
|
|
Post by Buzzer on Oct 22, 2006 2:24:45 GMT -5
I think i cut enouh off the front fenders for wheel clearance..... before>>> after>>> got some grinding to do, to clean it up and make smooth....
|
|
|
Post by poorboy1 on Oct 22, 2006 7:32:53 GMT -5
did you get the clutch in yet?
|
|
|
Post by Buzzer on Oct 22, 2006 10:51:12 GMT -5
had the clutch sence i got the truck,,,,, got the fly wheel resurfaced, picked up the engine rear oil seal, tranny gasket and t-case input seal... just waiting on a date when i can get it all installed..... and hopefully tune it over......
|
|
|
Post by Buzzer on Oct 23, 2006 18:15:05 GMT -5
|
|