|
Post by Jonny tsunami on Oct 22, 2014 22:47:11 GMT -5
ok started to tackle the electrical, got the computer wired into a waterproof box with the balk head connector mounted on the bottom. going to mount the other box drivers side for all the solenoids for the lights air locker and temp sensor for the fans. also cut the ac box back now I just need to skin it with aluminum to seal it up so the heater fan still works. and got this 20 inch light bar, and going to replace the 2 kc's with 4 small 6 led lights angle at 45s
|
|
|
Post by poorboy1 on Oct 22, 2014 23:15:03 GMT -5
coming together. better get it entered up in TTC.
|
|
|
Post by Rock Dawg on Oct 24, 2014 10:38:19 GMT -5
I think I need to do a better job on the jeep's waterproofing to computer system and plug connectors. I've seen several people use plastic kitchen or lunch boxes to keep the computers safe. I think that it how I will better water proof mine but I wanted to talk to Josh and Jason after there experiance with TTC and being under water. I'm sure they have great ideas from others at that compitition.
|
|
|
Post by stefanh on Oct 25, 2014 0:05:22 GMT -5
I moved mine underneath the dash above the glove box. If my cab goes under then ya I probably gotta get pulled haha
|
|
|
Post by Jonny tsunami on Oct 27, 2014 20:15:02 GMT -5
Got 25 feet of 3/8s hose and ran all my vent lines, front and rear axles and both transfer cases way up high. Got the fuel lines plumed, and tested it, fuel pressure is at 12 psi. not sure about adjusting it yet. at least its working and no leaks.
|
|
|
Post by Jonny tsunami on Dec 1, 2014 0:04:41 GMT -5
Got to the point of a test fire, and it did not start. added a little gas to the tbi blades and it fired a little. so I figure the injectors are not firing, google help me.
|
|
|
Post by Jonny tsunami on Dec 4, 2014 22:02:54 GMT -5
Got to get a new control module for the distributor is what I found after searching. And some new parts came today. single 3 inch exhaust universal kit
|
|
|
Post by Jonny tsunami on Dec 6, 2014 23:08:48 GMT -5
I know I'm getting a little crazy with the orange paint but what the hell right, it was bare so it needed it anyways
|
|
|
Post by Jonny tsunami on Jan 3, 2015 16:45:08 GMT -5
Good news bad news.. went and payed for a u-pull it computer 46 bucks and that didn't solve the no fire issues, but in the process I found that after unwrapping the wires that the two wires from the injectors are spliced together and ran as a red wire to the plug that would be attached to the fuse panel. some how when I was tracing those wires back I thought I had them going into the computer. so after unwrapping the harness I found it so now all I got to do is splice the red wire into the pink-black stipe wire. And now she runs
|
|
|
Post by Jonny tsunami on Jan 25, 2015 21:05:46 GMT -5
|
|
|
Post by poorboy1 on Jan 26, 2015 20:27:07 GMT -5
gonna be ready for the March run?
|
|
|
Post by Jonny tsunami on Jan 27, 2015 0:40:03 GMT -5
gonna be ready for the March run? well if I get it moving, doesn't have to be all done. If anything the crew will make it, maybe on paddles just to see what they will do.
|
|
|
Post by Jonny tsunami on Feb 1, 2015 12:41:15 GMT -5
wow, note to all, this does not fit over a 1410 yoke you have to remove it install the guard then reinstall the yoke. kinda a pain it the ass.
|
|
|
Post by Jonny tsunami on Feb 2, 2015 20:45:20 GMT -5
ok this is what I came up with for extra capacity for the assist. I know theres a lot of ways to do it but this is what I came up with.
|
|
|
Post by poorboy1 on Feb 5, 2015 22:00:34 GMT -5
is that the adapter i made? cool.
|
|