|
it runs
Apr 16, 2007 22:46:04 GMT -5
Post by popeye on Apr 16, 2007 22:46:04 GMT -5
i got behind over the weekend and did not get the engine done! but i did a little clean up today(i love my sawzall) kinda hard to see all the x-tra wires laying next to the ac condensor i took out here is a pic of the new trans installed
|
|
|
it runs
Apr 29, 2007 23:21:08 GMT -5
Post by popeye on Apr 29, 2007 23:21:08 GMT -5
got the bronco started today, still have alot of fine tuning to do but atleast it run
|
|
|
it runs
Apr 29, 2007 23:22:55 GMT -5
Post by ReBeL on Apr 29, 2007 23:22:55 GMT -5
|
|
|
it runs
Apr 29, 2007 23:48:08 GMT -5
Post by poorboy1 on Apr 29, 2007 23:48:08 GMT -5
|
|
|
it runs
Apr 30, 2007 6:53:02 GMT -5
Post by popeye on Apr 30, 2007 6:53:02 GMT -5
i will get pics up of it installed plus some others that i took in a couple days
|
|
|
it runs
Apr 30, 2007 10:14:48 GMT -5
Post by Brennerbadboy on Apr 30, 2007 10:14:48 GMT -5
nice pics
|
|
|
it runs
May 8, 2007 23:06:26 GMT -5
Post by popeye on May 8, 2007 23:06:26 GMT -5
here is a little up date! had to take things apart push rods were about .030" too short so after doing a little investagating found out that a olds 400/455 had the length i needed so put those in and finally realized their was a fitting for the pcv valve on the back of the carb. its running really good compaired to what it was.
|
|
|
it runs
May 8, 2007 23:08:11 GMT -5
Post by WILLYNILLY on May 8, 2007 23:08:11 GMT -5
Cool man!!! you should get a vid of it running on here!!!
|
|
|
Post by wotpos on May 9, 2007 0:59:40 GMT -5
i'd watch it
|
|
|
it runs
May 10, 2007 18:21:16 GMT -5
Post by norseman74d on May 10, 2007 18:21:16 GMT -5
|
|
|
it runs
May 11, 2007 23:24:43 GMT -5
Post by popeye on May 11, 2007 23:24:43 GMT -5
got the bronco back from the exaust shop today! i'll post some pics tomorrow of a bunch of stuff
|
|
|
it runs
May 13, 2007 22:31:17 GMT -5
Post by popeye on May 13, 2007 22:31:17 GMT -5
the on going process is getting closer and so is summer bash! got the front wheel bearings replaced this weekendthe left side was all a mess had to cut the inner bearing off. the inner nut was missing the locking tit plus it had stress cracks all over it. the right side was ok but still a mess. some pics to feed the need! water line on the inside of my door from the hole that killed my old eng. (i have a 4" lift w/35"tires) old engine new engine rh side header coming thru the fenderwell lh exaust after i got it back from the exaust shop
|
|
|
it runs
May 13, 2007 22:41:38 GMT -5
Post by poorboy1 on May 13, 2007 22:41:38 GMT -5
cool
|
|
|
it runs
May 13, 2007 23:40:39 GMT -5
Post by WILLYNILLY on May 13, 2007 23:40:39 GMT -5
Nice man!!! Lookin good
|
|
|
it runs
May 16, 2007 6:42:34 GMT -5
Post by popeye on May 16, 2007 6:42:34 GMT -5
after i put the hood back on today and top off all fluids i will be ready to hit the beach
|
|